Start with the key out of the ignition. I found out that if it is warmer, and I turn on ventilation for a while after it will let me go! What am I doing wrong? Lock and unlock the drivers door using the power lock switch on door panel. Be patient, the programming procedure can be frustrating. This has to be the single most aggravating thing to ever go through. I had my car programmed to recognize 2 used advanced keyremotes yesterday and this is the unbelievable story of great customer service mixed with a large dose of incompetence.
I am desperate , cannot use my car in winter at all or cold weather. And where could I find it on my 03 Mazda 6? I had the same thought about the doors after posting this message. Quickly open and close the driver's door again and push a button on the 2nd remote. The car tries to start but when you release the key it dies. Step 5: Open and close the drivers door 3 times. Car did Lock, Unlock, Trunk pop and Horn.
I have done it 3 times each the 4 time thing was a diagnostic to test the keyless system I was told. Close and open door three times or use the door switch button 6. You must get an Automotive Locksmith to program the remote to your vehicle for you. Can someone help me here? The Mazda dealership here told me that they don't deal with this type of keyless entry system. Needless to say you are allowed to drink while you play and being in the heat of the moment I grabbed my fob flipped the key out and stabbed a beer can to shotgun it. My experience with NorthCoast was great.
Press Prog … ramming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. Could not turn ignition off without jiggling key the last part of key extraction is the popout of the lock you can see. This sounds absurd, but it worked for us to program our new Mazda 5 Keyless Entry Keyfob. This process may be repeated for up to four keys. So i ordered the part to do it myself and tear the door apart to find out I have bigger problems.
Do this 3 times within 10 seconds. Leave key in the ignition. Leave key in the ignition. Program a Mazda keyless entry remote. I open my door the car beeps like I left my keys in the car. Well, needless to say, he was wrong.
I have done everything in this forum, even purchased a new remote and still nothing. Open Drivers door and leave open. Remove the key from ignition. Previous posts indicated this was to see if the keyless system was working properly, which I guess it is not. But when I continued past with no response, and I removed the key from ignition, I got the proper response. The unit will learns up to 4 different transmitter codes. Wait about 5 seconds, then remove the key.
Easy cash cow for the dealer I guess. Do not turn the key far enough to start the car, just to the 'on' position so the dashboard lights up. This is about half of what the dealership wanted. This works for the keyless entry but not for the immobilizer key. Step 6 someone tell me if i am on the correct path. Cycle key quickly but carefully on-off appr 10 times until the car honks one time. Remove key from ignition and locks should lock and unlock again.
In fact, many people recommend buying a spare key and doing this procedure so that you always have three working keys around you only receive two when you buy the car. This is how to program a Mazda protege keyless also works with other Mazda models remote system: 1. If you are having trouble, step away for a while and come back to it later. Hi people I have a question on behalf of my brother he has a mazda B-3000 Troy Lee Edition manual tranny I think it is 2000 or 2001 not sure. Step 5: Close and open the drivers door 3 times. Open and close drivers door 3 times ending with door in the open position.
I havent figured that out. Step 2: Lock and unlock the drivers door using the power door lock switch on the door. We appreciate all of your help! Now I need to tap one of the wires either hot wiring it from the parking lights or the ignition fuse in the cabin fuse box. Horn will sound once to indicate you are in remote programing mode if the horn does not sound start over. Step 1: Open drivers door and leave open.
Step 2 Lock and unlock the drivers door using the power door lock switch on the door. Very pleased with this company. Door should be left open after this step. Horn will sound 3 times to indicate the completion of the procedure. Any advice that is cheap? You should get 2 light flashes indicating the unit is waiting for a 2nd code, then press button 1 of a second transmitter, the unit will flash 3 times indicating its waiting for the 3rd code and so on. Door locks should respond by locking and unlocking.