The vehicle can be driven at a speed lower than that in the above diagram under the lock-up condition. If the diameter is greather than the maximum, replace the multiple disc clutch hub with a new one. D009189 C141534 C141534 A C134874E01 Mark Thickness Mark Thickness 1 1. If the result is not as specified, replace the shift solenoid valve. ·lbf Install starter assy 30. Only recommended automatic transaxle fluid or kerosene should be used for cleaning. If the result is not as specified, replace the shift solenoid valve.
This prevents the spring seat from being deformed. Open in shift solenoid valve S4 circuit 2. These upgrades and modifications are things the factory should have done in the first place. . Repair or replace the harness and connector.
If the body clearance is greater than the maximum, replace the oil pump body sub-assembly. Bolt C: 41 mm 1. Do you just have U250E questions and need some answers? Standard resistance c Measure the resistance according to the value s in the table below. Bolt C: 23 mm 0. All gaskets and rubber O-rings should be replaced with new ones. The standard voltage between the terminals is shown under Specific Condition.
Yes, you ready that correctly. None Time after engine start 16 min. If the free length is shorter than the standard free length, replace the forward clutch return spring sub-assembly. If the piston stroke is less than the minimum, parts may have been assembled incorrectly. Automatic transmission clutch, brake or gear, etc. Do not depend solely on these reference values when deciding whether apart is faulty or not.
They cannot be used to judge if a sensor or solenoid is defective or not. Standard resistance d Measure the resistance according to the value s in the table below. Install oil cooler outlet tube No. Standard resistance d Measure the resistance according to the value s in the table below. The object of this test is to check the overall performance of the transaxle and engine by measuring the stall speeds in the D position. When removing the piston, hold it by hand using a waste cloth.
The is the place where the industries best transmission rebuilders work together to help solve the most complex automatic transmission problems. All participants of this group must agree to the terms of our. Thrust Needle Roller Bearing Differential Gear Assembly Forward Clutch Assembly D025505E04 F - E Thickness Less than 7. Bearing and bearing race diameter: mm in. Bolt C: 42 mm 1.
Select a thrust bearing which satisfies the specified end play value and install it. Use these ranges as a reference. Resistance c Connect the positive + lead with a 21 W bulb to terminal 2 and the negative - lead to terminal 1 of the solenoid valve connector, then check the movement of the valve. Malfunction item: A metallic sound is emitted from the torque converter clutch assembly during the stall test or when the shift lever is moved to the N position. Make sure that the ends of a snap ring are not aligned with one of the cutouts and are installed in the groove correctly. None Time after engine start 15 min.
Torque: 34 N·m 350 kgf·cm, 25 ft·lbf 27. Bolt C: 42 mm 1. Standard resistance d Measure the resistance according to the value s in the table below. Standard resistance c Connect the positive + lead with a 21 W bulb to terminal 2 and the negative - lead to terminal 1 of the solenoid valve connector, then check the movement of the valve. If the pack clearance is not within the specified range, inspect the discs, plates, and flange. Remove all the pan bolts, and carefully remove the oil pan assembly. Furthermore, the same diagnostic items which are detected in the normal mode can also be detected in the check mode.
Bearing race diameter: mm in. Torque: Bolt A, B: 11 N·m 110 kgf·cm, 8 ft ·lbf Bolt C, D: 6. The component groups are inspected and repaired from the converter housing side. Driving distance after engine start 9 km 5. While driving in the 4 position and 4th gear, release the accelerator pedal and check the engine braking effect. Check mode is also available to technicians as an option.
Our members about how great our service is, and you will too! Check thrust bearings and races for wear or damage. If the inside diameter is greater than the maximum, replace the stator shaft. If a component group cannot be assembled because some parts are being ordered, be sure to keep all parts of the group in a separate container while proceeding with disassembly, inspection, repair and reassembly of other component groups. Standard resistance d Measure the resistance according to the value s in the table below. Install the valve body to the transaxle case with the 17 bolts. And some codes may not be detected through this drive pattern. This stops lock-up control, then fuel economy decreases.